90° Ecke anbringen

Durchschnittliche Bewertung (9):
     

  • Video ansehen
    Video ansehen
  • 90° Ecke anbringen
    Bildergalerie

Der einfache Weg um 90 ° Eckverbindungen und "T" Gelenke in Kästen, Schränke und Fällen zu halten

  • Werke auf 90° Ecken und Fugen "T"
  • Maximale Kapazität 1"
  • Aluminiumguss "V" und Keil anbringen-pads
  • Automaxx® Anpassung Auto--Technologie
  • Einfach zu regulieren Spanndruck mit Stellrad
  • Ausschnitt ermöglicht eine Tasche-Loch-Schraube anbringen ohne fahren
  • Gepolsterte, ergonomische Griffe

$44.99 USD

TEILE-NR.: KHCCC

Händler suchen

Beschreibung

The Kreg® 90° Ecke anbringen gibt Ihnen die helfende Hand, die Sie benötigen, um 90 ° Ecken und Fugen "T" gemeinsam sicher zu halten wenn Sie Kisten, Schubladen, Schränke und Fällen zusammenstellen sind. Darüber hinaus die 90° Ecke anbringen lässt beide Hände frei, um Ihre Verbindungselemente. 90° Ecke anbringen ist die schnellste und am einfachsten zu bedienende Ecke anbringen Sie dank Kreg Automaxx® Auto-Anpassung der Technologie kaufen können.

Die 90° Ecke anbringen halten Versammlungen wie Boxen, Schränke, Schubladen und Fällen zusammen hilft, um sicherzustellen, dass Sie starke, eng anliegende Assemblys erhalten – ob Sie Kreg Tasche-Loch Tischlerei oder eine andere Methode verwenden. Das anbringen V-Wedge Backen greifen die Paarung Stücke sicher, um sicherzustellen, dass die Stücke bei genau 90 ° Winkel beim Einfahren Kreg Schrauben oder auch eine andere Art der Befestigung, z. B. einen Nagel oder eine hölzerne Schraube sitzen.

Die 90° Ecke anbringen Funktionen Ganzmetall-Konstruktion, einschließlich Aluguss-Pads – eine äußere "V" und innere Keil – das Drücken gegen die innen- und Außenflächen der beiden zu verbindenden um diese Stücke zu halten ein 90°-Winkel zueinander. Rand stoppt helfen auch die Kanten der Teile präzise Montage von Strukturen wie Boxen, Schränke, Schubladen und Fällen darauf ausrichten.

Dank Automaxx® automatisch anpassen, Technik, alles, was du tun musst ist, drücken Sie die Griffe anbringen. Die anbringen schließt automatisch mit der Menge des Drucks, die Sie, unabhängig von den Materialien festgelegt haben, egal, ob Sie mit dünnem Sperrholz für Schubladen oder Materialien bis zu 1" Dick.

Technische Daten

Klemm-Kapazität

90° Ecke und "T" Gelenke in Materialien bis zu 1" Dick

Materialien

Geschmiedet, Stahl, Guss-Aluminium, wärmebehandelt, "V" und Keil, gepolsterte Griffe

Design

Selbst Quadratur; automatisch richtet Gelenke um 90° Winkel; Automaxx™ Anpassung Auto--Technologie

Stellschraube

Ermöglicht einfache Einstellung des Anpressdrucks

Lieferumfang

(1) 90° Ecke anbringen

Bewertungen für "90° Ecke anbringen"

Durchschnittliche Bewertung:
     

Clamp adjustment extremely poor

Brought the clamp for a project because the other corner clamps will not fit the micro jig size holes. The clamp is way out of adjustment from the factory and even following instructions from other users that have had the same problems it would work for one clamping but then be out of wack again preventing a second clamping without going through the same adjustment. I have always loved Kreg items from my router table trough the many clamps I have. This product is an extreme disappointment and needs to be completely redesigned.

     

By James Kersey

December 8, 2019

should have been five stars

I purchased 2 of these clamps. They did not work. Needed to get shelving done as inspection was rapidly coming up. Got so frustrated that I almost threw them out. Finally found someone who told me what to do. Now they work great. I have several Kreg tools and this is the only one that gave me problems. Need to improve these a little.

     

By Alden Allison

October 1, 2019

Good Tool, after 2 adjustments

The tool works great but I needed to make 2 adjustments to get it there. The first is that it had almost zero clamping pressure. I read somewhere how to fix this and it seemed to work. You need to back out the adjustment screw most of the way, cycle the tool, and then adjust it to the pressure you need. Kreg should do this at the factory so shame on them for delivering these in this condition. The 2nd adjustment was that the boards were noticeably out of square (1 to 2 degrees which amplifies over the cabinet distances of course as 1 deg = .017"/1"). I checked the jaws for flatness and squareness and saw that one jaw was slightly out of flat in the direction that was consistent with what I observed in the clamped boards. I took a file and carefully flattened the offending jaw and now they are quite square and repeatable. The clamp is now very handy to use and accurate. The disappointing thing is that Kreg could have produced the tool this way so it is not up to their normal quality standards and they should fix this before losing the public on a well conceived and useful tool

     

By Patrick Lorenz

July 1, 2019

Thought Clamp was broken but

The clamps did not work from the start, so I contacted Kreg. They responded the same day explaining how to reset the automaxx system on the clamps. They are not working like a charm. I will share the instructions on how to reset the automaxx system, as I could not find them in the FAQs. So you will open the jaws and back out that adjustment screw to the point where it is really loose but not falling out. You should see around 3/8" of threads between the bottom of the head of the screw to where it screws into the mechanism. Then you will close the jaws then open them back up. After that, you can bring that adjustment screw back to the positive around halfway down and try to clamp it down. That adjustment is not an exact adjustment, you may have to tighten it more or loosen it more to get the correct pressure you want to apply. When you are using the clamp, you will want to make sure you are opening the clamp fully when you are moving the clamp. This will allow the Automaxx system to reset to zero each time. You should only need to adjust the adjustment screw if you need to add or take out pressure from the clamp as the clamp will adjust to different thicknesses on its own.

     

By Scott Lenninger

February 20, 2019

Adjustment Screw

Looked like a great tool, unfortunately could not get the adjustment screw to work and lost time on a project because I had to take it back to store to get my money back. Fix the adjustment screw and this will be a really great tool.

     

By James O'Sullivan

October 25, 2018

Weitere Bewertungen lesen

This website uses first party and third party cookies to improve your experience and anonymously track site visits. By visiting this website, you opt-in to the use of cookies. OK