Deckenleisten-Pro

Durchschnittliche Bewertung (7):
     

Nehmen Sie das Rätselraten schneiden Kronenform

  • Easy-to-Use für innen- und Außenecken
  • Arbeiten mit Kronenform bis zu 51/2"(138mm) breit
  • Eliminiert die Notwendigkeit für schwierige Verbindung Winkelschnitte
  • Im Preis inbegriffen Winkelmesser sorgt für genaue Ergebnisse
  • Sockel in jedem Frühjahr Winkel zwischen 30-60 ° arretierbar
  • 8 rutschfeste Gummifüße garantieren ein solides Fundament
  • Einfache Anweisungen zeigen, wie Sie die richtigen schneiden jedes Mal

$29.99 USD

TEILE-NR.: KMA2800

Händler suchen

Beschreibung

Krone-Spritzgießen anzubringen, ist eine der besten Möglichkeiten, um sofortigen Mehrwert für Ihr Zuhause. The Kreg Crown-pro™ vereinfacht das frustrierendste Schritte des Prozesses, so dass Sie weniger Fehler machen und die Arbeit schneller erledigt!

Exakte Winkel
Dieses einzigartig gestalteten Tool hält Ihre Trim im genauen Winkel erforderlich, wodurch die Notwendigkeit für fortgeschrittenen zusammengesetzten Gehrungsschnitte und schwer "meistern."

Vielseitig & kompatibel
Es hat gebogene Design können, die Sie eine Vielzahl von Kronenform Frühling Winkel ausgleichen, und seiner Erweiterung Arme können arbeiten Sie mit Krone bis zu 51/2"(140mm) breit.

Einfach Winkelmesser
The Crown-pro™ verfügt über eine einstellbare Winkel-Finder, die leicht Ihnen den genauen Winkel von innen und außen Ecken zeigt. Plus können Sie den Winkelmesser, um den Frühling Winkel des Krone-Spritzgießen zu überprüfen.

10"(254mm) Sägen arbeiten mit Krone bis zu 31/2"(89mm) breit, je nach Hersteller.
12"(305mm) Sägen arbeiten mit Krone bis zu 51/2"(140mm) breit, je nach Hersteller.

Für Kunden mit Wohnort in Kalifornien: Informationen bezüglich Proposition 65

Technische Daten

10"(254mm) Sägen

Arbeiten mit Krone bis zu 31/2"(89mm) breit, je nach Hersteller.

12"(305mm) Sägen

Arbeiten mit Krone bis zu 51/2"(140mm) breit, je nach Hersteller.

Lieferumfang

(1) Krone-Pro™ und des Besitzers Handbuch

Bekanntmachung

Vorschlag 65

Handbuch Nordamerikanisches Handbuch

Bewertungen für "Crown-Pro™"

Durchschnittliche Bewertung:
     

Not all that great

Although I was able to get good clean angles with this jig, I did have some issues with it. The little shelf under the molding is not wide enough, and allowed the workpiece to slide off. I really had to concentrate on lining it up horizontally, because the molding wouldn’t sit on the jig. The other big issue is that multiple times I had the cut-off piece kick out the back of the saw really hard. Pretty dangerous, and I’m glad there weren’t any windows or people in that direction. I think this is caused by the jig holding the workpiece above the saw table, with no support for the cut off section.

     

By Jeremy Marshall

June 2, 2019

I love this product. saved me a lot of money by doing my molding myself

I was prepared to pay I figured about 2 grand to have someone install crown molding in my house. but after watching videos on you tube, and reading about this jig, I ended up buying a dewalt t milter saw on Black Friday, 12 inch blade, and ordered the crown-pro. after practicing on a few scrap pieces of crown, I stated to cut and install. I only did inside cuts for one room, and the crown-pro made it very easy to cut inside corners. I dont normally do fanatic work on my home projects, but the crown pro made the job very easy, and the first room I installed crown molding came out great. going to do the whole house and save a lot of money. love my crown-pro

     

By dave paul

December 7, 2017

Underneath Red setting

The red setting gauge underneath the unit should be a medal guide with black degree markings. It would set much more precisely with this design. Also it would make the spring angle setting easier in the instruction manual to state "use the vertical side of the pointer to the angle desired". The slope side shows 40 in the illustration which can be misleading. The manual picture shows such but words would also help the novice.

     

By James Jackson

November 29, 2017

Needs robustness

The jig suffers from distortion when pressure is place on one end or another to hold the stock in place. During installation of 1600 feet of molding we found first that the angle adjustment had slipped (perhaps not tightened enough), but then after marking the seating on each end to watch for slippage, we discovered that one end had twisted. The lower lip was also flexible, and for our molding it would have been nice to be a bit deeper. Finally, it would be nice to have cork or rubber on the face to help steady the stock. We'll continue to use it with the above precautions, but a second, more robust version should be planned. For a big job, we would use two jigs to avoid moving it back and forth from left to right side of the saw blade.

     

By Frederick Grose

April 26, 2017

Awsome Product

We purchased this to put crown molding in the kitchen. After reading the manual, watching the product video, and watching the crown molding installation video with professional builder Gary Streigler we got our crown molding up first time no problems. If you do what I said above you will have no problems either. Someone said the manual did not say to cut the molding upside down (the most decorative side up) you are wrong and did not read the manual because it is in there.

     

By Ron Bertke

July 4, 2016

Weitere Bewertungen lesen

Inspirationen

This website uses first party and third party cookies to improve your experience and anonymously track site visits. By visiting this website, you opt-in to the use of cookies. OK